ProductWet Boot Washers
B65256 Motorised Walk-Through Boot Washer with Drying Section
Image indicative of the range. Configurations may differ.
1 / 3 product images
Two-station walk-through boot washer and dryer with sensor activation, two 0.37 kW 380 V three-phase motors, built-in motor overload protection, peristaltic soap dosing and removable grid steps. Separate electrical supply to each station enclosure. Air-assisted drying and heating are optional.
Typical lead time: ± 10-15 working days. Final timing will be confirmed in your quotation.
Price on request
Choose the quantity you need and add this item to your quote. We will confirm final pricing and delivery.
Share this model with a colleague or reopen its specifications later.
Shortlist this configuration, add project notes and compare your options.
Product overview
The Basterfield B65256(RS-380), based on the B65250 walk-through boot washer, cleans and dries the soles of safety boots in two consecutive stations. Users step directly from the wet wash station onto the drying station. Each station has automatic sensor activation, an independent motor drive, its own electrical enclosure and a separate catchment tray. The unit has Grade 304 stainless steel construction.
Washing and drying
Wet wash station. Rotary brushes with black nylon bristles scrub the boot soles while water and detergent are applied. A peristaltic pump meters the detergent. The dosing rate is adjusted via a PWM controller in the electrical enclosure and calibrated during commissioning for the selected detergent and water flow. The chemical remains inside the tubing without contacting the pump mechanism. Use chemicals compatible with the PVC chemical transport tubing that will not corrode or degrade it.
Drying station. Higher-speed rotary brushes remove residual water from the soles. The drying station is designed to leave boot soles free of dripping water on exit. Optional air-assisted drying helps keep the brushes dry during repeated use and adds approximately 1–2.5 kW when fitted. Supplementary heating is available where required.
Capacity and operation
One person can use each station, and both stations can operate simultaneously. Each station grid supports a user weighing up to 250 kg. Indicative throughput is approximately 3–4 users per minute under steady flow, allowing approximately 15 seconds per station.
Each station has a 0.37 kW, four-pole, 380 V three-phase motor. Motor starters have built-in current overload protection. The sensors, solenoid valves and detergent dosing system use a 12–24 V DC control supply. Automatic sensors activate operation, and twist-release emergency stops require a manual reset before operation can resume.
Installation
The unit is supplied fully pre-wired. The site must provide a separate 380 V three-phase electrical supply to each station enclosure: one supply for the wet station and one for the drying station. Each supply requires three phases, neutral and protective earth, with a suitably sized cable and gland. Each incoming supply terminates at the enclosure’s four-pole isolator, with a dedicated earth terminal inside the enclosure. Total connected load depends on the selected drying and heating configuration.
Provide a water supply to the ½″ BSP female inlet. Recommended minimum supply pressure is 3 bar (300 kPa). Typical washing flow is 10 L/min, adjustable via the inlet choke valve. Provide 1½″ BSP waste pipework to carry water away from the separate female outlets for wet-station waste and dry-station wash-down.
Removable grid-style stainless steel access steps are supplied as standard for ease of cleaning. Overall dimensions and platform height are shown on the general arrangement drawing.
Maintenance and warranty
Routine maintenance includes cleaning, brush inspection and gearbox lubrication. Replacement brush sets are available. The unit carries a 12-month warranty on parts and workmanship. Normal wear, brushes and heating elements are excluded.
Product data
Specifications & models
Specifications
Specification support
Need a second set of eyes?
Installation & support
Technical information & documents
Product documents
Download installation, specification and warranty PDFs.
Product specification sheet
Dimensions, materials and product data.
PDF
Product warranty
12-month warranty and claims information.
PDF
Technical media
Need a drawing, CAD file or compliance certificate?
Request technical files








